From 40f81d08239763c2b5c05af63f17e3fd098d978d Mon Sep 17 00:00:00 2001 From: pants Date: Mon, 21 Sep 2026 14:16:02 -0700 Subject: init --- nut/titanium/upsd.conf | 186 +++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 186 insertions(+) create mode 100644 nut/titanium/upsd.conf (limited to 'nut/titanium/upsd.conf') diff --git a/nut/titanium/upsd.conf b/nut/titanium/upsd.conf new file mode 100644 index 0000000..78fe0fa --- /dev/null +++ b/nut/titanium/upsd.conf @@ -0,0 +1,186 @@ +#LISTEN 127.0.0.1 3493 +# Network UPS Tools: example upsd configuration file +# +# This file contains access control data, you should keep it secure. +# +# It should only be readable by the user that upsd becomes. See the FAQ. +# +# Each entry below provides usage and default value. +# +# For more information, refer to upsd.conf manual page. + +# ======================================================================= +# MAXAGE +# MAXAGE 15 +# +# This defaults to 15 seconds. After a UPS driver has stopped updating +# the data for this many seconds, upsd marks it stale and stops making +# that information available to clients. After all, the only thing worse +# than no data is bad data. +# +# You should only use this if your driver has difficulties keeping +# the data fresh within the normal 15 second interval. Watch the syslog +# for notifications from upsd about staleness. + +# ======================================================================= +# TRACKINGDELAY +# TRACKINGDELAY 3600 +# +# This defaults to 1 hour. When instant commands and variables setting status +# tracking is enabled, status execution information are kept during this +# amount of time, and then cleaned up. + +# ======================================================================= +# ALLOW_NO_DEVICE +# ALLOW_NO_DEVICE true +# +# Normally upsd requires that at least one device section is defined in ups.conf +# when the daemon starts, to serve its data. For automatically managed services +# it may be preferred to have upsd always running, and reload the configuration +# when power devices become defined. +# +# Boolean values 'true', 'yes', 'on' and '1' mean that the server would not +# refuse to start with zero device sections found in ups.conf. +# +# Boolean values 'false', 'no', 'off' and '0' mean that the server should refuse +# to start if zero device sections were found in ups.conf. This is the default. + +# ======================================================================= +# STATEPATH +# STATEPATH /var/run/nut +# +# Tell upsd to look for the driver state sockets in 'path' rather +# than the default that was compiled into the program. + +# ======================================================================= +# LISTEN [] +# LISTEN 127.0.0.1 3493 +# LISTEN ::1 3493 +# LISTEN myhostname 83493 +# LISTEN myhostname.mydomain +# +# With no LISTEN statement, the default is localhost and port 3493. +# In case of IP v4 or v6 disabled kernel, only the available one will +# be used. +# Note that it is not true for Windows platforms. You shouldn't use IPv6 in +# your configuration files unless you have IPv6 installed. +# +# As a special case, `LISTEN * ` (with an asterisk) will try +# to listen on "ANY" IP address for both IPv6 (::0) and IPv4 (0.0.0.0), +# subject to `upsd` command-line arguments, or system configuration. +# Note that if the system supports IPv4-mapped IPv6 addressing per RFC-3493, +# and does not allow to disable this mode, then there may be one listening +# socket to handle both address families. +# +# One or more LISTEN statements give the IP address (or name that +# resolves to such an address) for upsd to listen on, optionally with +# a port number. +# +# As an example, a machine with a LAN and a WAN interface that also +# functions as a router and firewall might be configured to listen +# only on the LAN interface. +# +# This will only be read at startup of upsd. If you make changes here, +# you'll need to restart upsd, as reload will have no effect. +# +# Please note that older NUT releases could have been using the IPv4-mapped +# IPv6 addressing (sometimes also known as "dual-stack") mode, if provided +# by the system. Current versions (since NUT v2.8.1 release) explicitly try +# to restrict their listening sockets to only support one address family on +# each socket, and so avoid IPv4-mapped mode where possible. + +# ======================================================================= +# MAXCONN +# MAXCONN 1024 +# +# This defaults to maximum number allowed on your system. Each UPS, each +# LISTEN address and each client count as one connection. If the server +# runs out of connections, it will no longer accept new incoming client +# connections. Only set this if you know exactly what you're doing. + +# ======================================================================= +# CERTFILE +# CERTFILE /usr/local/ups/etc/upsd.pem +# +# When compiled with SSL support with OpenSSL backend, +# you can enter the certificate file here. +# The certificates must be in PEM format and must be sorted starting with +# the subject's certificate (server certificate), followed by intermediate +# CA certificates (if applicable_ and the highest level (root) CA. It should +# end with the server key. See 'docs/security.txt' or the Security chapter of +# NUT user manual for more information on the SSL support in NUT. +# +# See 'docs/security.txt' or the Security chapter of NUT user manual +# for more information on the SSL support in NUT. + +# ======================================================================= +# CERTPATH +# CERTPATH /usr/local/ups/etc/cert/upsd +# +# When compiled with SSL support with NSS backend, +# you can enter the certificate path here. +# Certificates are stored in a dedicated database (split into 3 files). +# Specify the path of the database directory. +# +# See 'docs/security.txt' or the Security chapter of NUT user manual +# for more information on the SSL support in NUT. + +# ======================================================================= +# CERTIDENT +# CERTIDENT "my nut server" "MyPasSw0rD" +# +# When compiled with SSL support with NSS backend, +# you can specify the certificate name to retrieve from database to +# authenticate itself and the password +# required to access certificate related private key. +# +# See 'docs/security.txt' or the Security chapter of NUT user manual +# for more information on the SSL support in NUT. + +# ======================================================================= +# CERTREQUEST +# CERTREQUEST REQUIRE +# +# When compiled with SSL support with NSS backend and client certificate +# validation (disabled by default, see 'docs/security.txt'), +# you can specify if upsd requests or requires client's' certificates. +# Possible values are : +# - 0 to not request to clients to provide any certificate +# - 1 to require to all clients a certificate +# - 2 to require to all clients a valid certificate +# +# See 'docs/security.txt' or the Security chapter of NUT user manual +# for more information on the SSL support in NUT. + +# ======================================================================= +# DISABLE_WEAK_SSL +# DISABLE_WEAK_SSL true +# +# Tell upsd to disable older/weak SSL/TLS protocols and ciphers. +# +# With relatively recent versions of OpenSSL or NSS it will be restricted +# to TLSv1.2 or better. +# +# Unless you have really ancient clients, you probably want to enable this. +# Currently disabled by default to ensure compatibility with existing setups. + +# ======================================================================= +# DEBUG_MIN +# DEBUG_MIN 2 +# +# Optionally specify a minimum debug level for `upsd` data daemon, e.g. for +# troubleshooting a deployment, without impacting foreground or background +# running mode directly, and without need to edit init-scripts or service +# unit definitions. Note that command-line option `-D` can only increase +# this verbosity level. +# +# NOTE: if the running daemon receives a `reload` command, presence of the +# `DEBUG_MIN NUMBER` value in the configuration file can be used to tune +# debugging verbosity in the running service daemon (it is recommended to +# comment it away or set the minimum to explicit zero when done, to avoid +# huge journals and I/O system abuse). Keep in mind that for this run-time +# tuning, the `DEBUG_MIN` value *present* in *reloaded* configuration files +# is applied instantly and overrides any previously set value, from file +# or CLI options, regardless of older logging level being higher or lower +# than the newly found number; a missing (or commented away) value however +# does not change the previously active logging verbosity. -- cgit v1.2.3